Definitive Technology AW6500 Bedienungshandbuch PDF herunterladen (Seite 6)

screw inserts on the end panels and the metal screws on the bracket knobs.

Carefully mask both bafﬂes to protect the drivers, tweeters, low-bass

radiators, and bafﬂes [ﬁgure C]. Make sure the tape forms a tight seal around

the edges so that no paint can get on the bafﬂe or speaker parts. If paint gets

on the speaker parts (driver, tweeter, Low Bass Radiator), it will affect the

sound and is not covered by the warranty. The grille features an engraved

logo badge. You can remove it before painting the grille or paint right over it.

Painting the Cabinet, Bracket

Knobs and Bracket

1. Apply two thin coats of primer to the

cabinets and locking knobs. The brackets

do not require primer.

2. When the primer is completely dry,

apply the ﬁnish color [ﬁgure D].

3. When the paint is completely dry,

remove the masking materials.

4. Do not re-attach the speaker to the

bracket until the bracket is mounted.

Try to keep all handling of freshly

painted parts to a minimum.

Painting the Grille

1. The grille features an even, protective

powder coating. This powder coating is

an ideal primer. The grille features an

engraved logo badge. You can remove it

before painting the grille or paint right over

it. Rotate the logo badge to its horizontal

or vertical orientation prior to painting

the grille.

2. Using spray paint, spray two thin coats

of ﬁnish color with no primer [ﬁgure E].

If you’re using a compressor and spray

gun, use the ﬁnest, most diffuse setting.

Be careful not to ﬁll the holes in the grille

with paint.

3. When the paint is completely dry, carefully ﬁt the grille into its recess

so that it is just resting on the cabinet. Starting with one corner, go around

the speaker and push the grille into the grille notch a little bit at a time.

Be gentle; the grille may be easily bent out of shape by rough handling.

Paint Mask P

Paint Mask Pa

Paint Mask P

Paint Mask

Paint Mask P

Paint Mask Pa

Paint Mask P

Paint Mask

P Paint Mask

Paint Mask

P Paint Mask

Paint Mask

P Paint Mask

Paint Mask

Mas

Pain

t Ma

Pain

t Mask

Pai

Mas

Pain

t Ma

Pai

Mask Paint M

Pai

Mas

Paint Ma

Pai

Mas

Pai

nt Mas

int

Pai

Mask

int

Pain

t Ma

k Paint M

Paint Ma

Pai

int

The AW speakers can be mounted vertically or horizontally but remember to

always point the speaker in such a way as to allow water to roll off the driver cone

and/or Low Bass Radiator.

Installation of AW Series Loudspeakers requires basic skills in using tools such

as a drill and screwdriver. If you are in doubt that you possess the necessary skills

or tools, consult your Deﬁnitive Technology dealer, general contractor or a

professional installer.

To mount the speakers, remove the bracket, mount the bracket to the surface,

and then re-attach the speaker to the bracket, re-insert the locking knobs and

tighten. Aim the speaker so that the driver/tweeter side points as directly as

possible toward the listening area.

Detailed Mounting Directions

1. Make sure the mounting hardware and surface you choose are both capable of

holding the weight of the speaker (see speciﬁcations on page 11) combined

with the force generated by strong wind and/or snow accumulations common

to your area.

2. Make sure the locations you select do not conceal electrical wiring or

plumbing behind the surface.

3. Prior to installation, hold the speaker in the chosen location to make sure it

safely clears obstacles such as ceiling, adjacent walls, corners, beams, lighting

ﬁxtures and door/window frames.

4. Remove the bracket and locking knobs by turning them counter-clockwise

until they come completely out of the cabinet.

5. Using the slots in the bracket as a template, mark the screw locations with

a pencil.

6. If you are certain that there is a stud

behind the wall surface, drive #10 screws

(not included) through the

wall and into the stud [ﬁgure F].

7. If there is no stud behind the wall

at the chosen location, install wall anchors

(not supplied) into the wall

by following the wall anchor

manufacturer’s instructions. Always

use two wall anchors and two screws per

speaker [ﬁgure F]. We do

not provide mounting screws or other hardware because we do not know what

kind of material you will be attaching the speaker to. For wood surfaces and

studs, use wood screws; for sheetrock or gypsum, you should use wall

anchors; for masonry, use masonry anchors.

Mounting AW Series Speakers

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Definitive Technology AW6500 Bedienungshandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Lautsprecher Definitive Technology AW6500